furuno navnet installation manual

) Antenna unit, clamping the rotation detector cable 13. Follow the instructions on the label inside the mounting base to secure the snap assy. 14. Mounting the antenna unit of MODEL1833C-BB 1. J801 Cable entry to one of the screws of the cable clamping plate Signal cable, antenna unit side J802 MD-9208 J611. Cable entrance Cable clamping plate EMI core E04SS251512 (Above cable clamping plate) 11. Fix the shield cover. Do not pinch the cable. 12. Attach the radome cover, aligning triangle mark on radome cover with that on radome base. Mounting bracket 1 Type: OP03-92 Code No.: 008-445-070 Hex. bolt Hex. bolt Mounting plate Support plate (1) Support plate (2) Bracket (1) Bracket (2) Any obstruction will cause shadow and blind sectors. Using outside fixing holes of the antenna housing Use the hex head bolts (supplied) to mount the antenna unit as below. 1. Fasten by tightening nuts. Do not fasten by tightening the hex bolts;. Ground wire Ground wire GROUND TERMINAL How to coat ground point and ground terminal with silicone sealant 1-22 Hex bolt Flat washer Flat washer Spring washer Hex nut Silicone sealant Hex nut. Use hex head bolts, flat washers, spring washers and nuts (local supply) to mount the antenna unit, confirming length of bolts. 1. In order to minimize the chance of picking up electrical interference, avoid where possible routing the signal cable near other onboard electrical equipment. Also, avoid running the cable in parallel with power cables. Tubing CABLE GLAND Four screws Antenna unit chassis, cover opened Antenna unit chassis, cover opened Shield Bolt. Lead in cable here. EMI core RFC-13 10. The power supply unit can be installed almost anywhere provided the location is dry, well-ventilated, sufficient maintenance space is provided and is installed within 5 m (cable length) from the processor unit. GD-1900C-BB: Do not remove the waterproofing cap. Wrap the connector nut and cap with vinyl tape as shown below.

• furuno navnet installation manual, furuno navnet vx2 installation manual, furuno navnet 3d installation manual, furuno navnet service manual, furuno navnet vx1 installation manual, furuno navnet vx2 service manual, furuno navnet installation manual, furuno navinet installation manual pdf, furuno navinet installation manual download, furuno navinet installation manual 2017, furuno navinet installation manual 2016, furuno navnet vx2 installation manual.

All rights reserved.This is possible - Ask your FURUNO representative or dealer to provide this feature.Each NavNet product is assigned an IP address to enable transfer of images between other NavNet products. For example, video plotter pictures can be transferred to a radar and vice versa. For flush mounting, the optional flush mount kit is required. When selecting a mounting location for the control unit keep the following in mind: Keep the control unit out of direct sunlight. Name Hanger fixture Hanger fixture Tapping screw Hex bolt 1. Fix the hanger fixture 19-023-1062 on a desktop with four tapping screws (5x20). 2. Fix the hanger fixture 19-023-1061 to the rear panel of the control unit with four M4x10 (supplied as accessories). Select a mounting location considering the points below. Locate the unit out of direct sunlight. Select a location where temperature and humidity are moderate and stable. Consider the length of the cable connected among the processor unit, antenna unit (or power supply unit) and control unit. Install the antenna unit on the hardtop, radar arch or on a mast on an appropriate platform. (For sailboats, a mounting bracket is optionally available.) It should be placed where there is a good all-round view with, as far as possible, no part of the ship’s superstructure or rigging intercepting the scanning beam. Save mounting hardware to use it to fix the antenna unit to the mounting platform later on. Cable entry Antenna unit, showing location of mounting hardware 2. Use the hole next to screw hole inside the cover to hang it. Unfasten the snap assy.Unwind the string. Cable clamps Shield plate Pan head screws M4x8 9 pcs. Caution: Be careful not to pinch the rotation detector cable when remounting the shield plate. Note 1: Be sure the shrink tube on the antenna cable does not contact the gasket. Note 2: Pinch the gasket tightly and insert it into the cable entrance. Cable clamps Cable tie (Another should be inside.

Page 8 and 9: Single-unit NavNet system (GD-1900C Page 10 and 11: Two-unit NavNet system Radar Antenn Page 12 and 13: Mounting procedure Flush mounting F Page 14 and 15: 1.2 Mounting the Processor Unit The Page 16 and 17: Mounting the antenna unit of MODEL1 Page 18 and 19: 5. Unfasten the rotation detector c Page 20 and 21: 9. Attach connectors of the antenna Page 22 and 23: 1-12 M8 x 20 Fixing plate Bracket ( Page 24 and 25: 1-14 Effective thread length 25 mm Page 26 and 27: 10.Thank you, for helping us keep this platform clean. The editors will have a look at it as soon as possible. D-1 INTERCONNECTION DIAGRAM. S-1 www.furuno.com All brand and product names are trademarks, registered trademarks or service marks of their respective holders.Thank you, for helping us keep this platform clean. The editors will have a look at it as soon as possible. Please try again.Register a free business account Exclusive access to cleaning, safety, and health supplies. Create a free business account to purchase Please try your search again later.You can edit your question or post anyway.Contains the following sections: Safety Instructions, Equipment Lists, System Configurations, Mounting, Wiring, Adjustment, Options, packing Lists, Outline Drawings, Interconnection Diagrams. Only contains instructions pertaining to installation. Does NOT contain any operator or system usage instructions which are sold separately. To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzes reviews to verify trustworthiness. Acquired as part of a lot from a marine electronics store down sizing obsolete inventory. If you have ANY questions please always feel free to send an eBay message or call Max Marine Electronics Inc, Pompano Beach, Florida for help, assistance or more detailed information.

Waterproofing cap and connector nut, sectional view DATA1 to DATA3 Other equipment can be connected to DATA1-DATA3 as shown below. Available equipment are shown below.Ship's power terminal board Replacement of the fuse The power supply unit is shipped with a 15 A fuse. Replace the 15 A fuse with a 7 A fuse (supplied) when the ship’s battery is 24 VDC. Change the address (last three digits; 001 to 254) when like models are connected directly or through the hub. Do this change before connecting the equipment to the other equipment or hub in order to distinguish equipment. Do not set the same IP address in the network. Open the INSTALL SETUP menu, and then press the B: RADAR SETUP soft key to display the RADAR SETUP menu. When the message “RADAR DOES NOT TRANSMIT.Default setting is “F”. Select the antenna type referring to the table shown below. MODEL1823C-BB MODEL1833C-BB MODEL1933C-BB MODEL1943C-BB MODEL1953C-BB TUNING MODEL 1953C-BB: Go to “Tuning for 1953C-BB power supply unit”, and then “Antenna tuning”. Therefore, a small but conspicuous target dead ahead visually should appear on the heading line (zero degrees). In practice, you will probably observe some small error on the display because of the difficulty in achieving accurate initial positioning of the antenna unit. Enter time difference between local time and UTC time.Use the A:W E soft key to switch coordinate. Disable Satellite Every GPS satellite is broadcasting abnormal satellite number (s) in its Almanac, which contains general orbital data about all GPS satellites, including those which are malfunctioning. One of the following displays appears depending on your selection.To use the processor unit as a remote system, do the following: 1. External buzzer Type: XH3-BZ-L970 Code no.: 000-146-422 1. Unfasten 11 screws and 9 connectors to remove the cover. 2. Use a knife to cut a “cross” in the rubber bushing on the rear cover. 3. Page 6 and 7: Optional supply Name Type Code No.

MODEL1954C-BB, 4ft, 48 rpm. MODEL1954C-BB, 6ft, 24 rpm. MODEL1964C-BB, 4ft, 24 rpm. MODEL1964C-BB, 4ft, 48 rpm. MODEL1964C-BB, 6ft, 24 rpm. For MODEL 1954C-BB. For MODEL 1964C-BBFor ant. unit of Model 1824C-BBFor ant. unit of Model 1834C-BBFor ant. unit of Model 19xxC-BBRemarksFor Processor unit:For 1964C-BB, 10m RW-9771 cable. For 1964C-BB, 15m RW-9771 cable. For 1964C-BB, 20m RW-9771 cable. For 1964C-BB, 30m RW-9771 cable. For power supply unit of 1954C-BBInst. Mat. CP03-24501. InstallationAccessories. Spare parts. For power supply unit of 1964C-BBInst. Mat. CP03-30601Fuses for 1964C-BB’s powerFuses for 1954C-BB’s powerFuses for processor unit. Optional supply. Name. Rectifier. External buzzer. Cable assy. ARP kit. Mounting bracketEMI core. Ring unit. Desktop mountingCable assy. Control unit. AIS interface. TypeFor GD-1920C-BB, 100 VAC. For GD-1920C-BB, 110 VAC. For GD-1920C-BB, 220 VAC. For GD-1920C-BB, 230 VAC. For MODEL seriesFor remote display, 20 m. For remote display, 30 m. ARP Board, for radarSpecify when ordering. For remote display cableFor trackball of control unit. For control unit RCU-017For NavNet, 5 m. For NavNet, 10 m. For NavNet, 20 m. For NavNet, 30 m. For navaid, 5 m, 6P-6P cross. For navaid, 10 m, 6P-6P cross. For compass, 10 m, 6P-6PAdapter cable for HUB. For monitor D-sub 15Cable between processor unitEach NavNet product isThe number of processor units which may be installed depends on the number of networkFor one network sounder: one radar and three plotters, or four plotters. For two network sounders: one radar and two plotters, or four plotters. Antenna UnitEcho sounder. Processor unitWeather stationAIS InterfaceTransponder FA-150RectifierReceiverNetwork. SounderGPS receiverWeather stationExternal buzzer. AIS Interface. VGA monitor. Remote displayRemote. ControllerNavigatorFacsimile. ReceiverSounderNavNet system: GD-1920C-BB. Note: The output signal from the processor unit for a monitor is as follows. RGB signal: Analog 0.

We always want to be transparent with our customers and fully disclose any information regarding the products we sell. A solution-minded staff, well versed in product functionality, compatibility and repair, is key to your satisfaction. International customers please allow up to 6 weeks for delivery. If you have ANY questions please always feel free to send a message or call Max Marine Electronics Inc, Pompano Beach, Florida for help, assistance or more detailed information. We always want to be transparent with our customers and fully disclose any information regarding the products we sell. A solution-minded staff, well versed in product functionality, compatibility and repair, is key to your satisfaction. SAFETY INSTRUCTIONS.i. EQUIPMENT LISTS.ii. SYSTEM CONFIGURATIONS.ivAll brand and product names are trademarks, registered trademarks or service marks of their respective holders. The paper used in this manualNishinomiya, 662-8580, JAPAN. Fax. All rights reserved. Printed in JapanRadiation Hazard. The radar antenna emits electromagneticOnly qualified personnelWear a safety belt and hardDistances at which RF radiation levels ofSerious injury or death canNote: If the antenna unit is installed at aConstruct a suitable service platformSerious injury or death can result if someone falls from the radar mast. Turn off the power at the mains switchboard before beginning the installation. Fire, electrical shock or serious injury canProcessor unit. Control unit. MODEL1824C-BB antenna unit. MODEL1834C-BB antenna unit. MODEL1934C-BB antenna unit. MODEL1944C-BB antenna unit. MODEL1954C-BB antenna unit. MODEL1964C-BB antenna unit. StandardDistance toWorst caseWorst caseWorst caseNil. Worst caseNil. Worst caseWorst caseWorst caseWorst caseWorst caseWorst caseWorst caseName. Control unit. Processor unit. Antenna unit. Power supply unit. Power supply unit. TypeMODEL1934C-BB, 48 rpm. MODEL1944C-BB, 24 rpm. MODEL1944C-BB, 48 rpm. MODEL1954C-BB, 4ft, 24 rpm.

POWER BoardS111 on the POWER Board to the upward (TUNE ADJ)Then, the radar’s video and tuningThus, at theA trigger pulse generated in the display unit goes to the antenna unit through the signalThe time taken by the signal to travel up toDuring thisWhen the display unit isThe range of objects will also beExamples of improper and correct sweep timingENTER knob to finish.Main bang is the “black hole” whichRotate the ENTER knob to suppress theLongitude. Offset. As above but for longitude. Use the WDisable. Satellite. Every GPS satellite is broadcastingAlmanac, which contains general orbitalAlmanac sometimes may not containEnter satellite number (max. 3ENTER soft key. Latitude. Set initial latitude position after coldLongitude. Set initial longitude position after coldAntenna. Height. Enter the height of the GPS antennaSmoothing. Latitude OffsetGPS SETUP menu description (con’t from previous page). Item. Description. Settings. Default Setting. Fix Mode. Choose position fixing method: 2DCold Start. Clears the Almanac to receive the latest. Almanac. No, Yes. No. WAAS setup. Press the D: WAAS SETUP soft key at the GPS SETUP menu to show the WAAS SETUPContents of WAAS SETUP menu. Item. Description. Settings. Default Setting. WAAS Mode. Select ON to use the WAAS mode. On, Off. OffWAAS satellite can be searchedAuto, Manual. Auto. WAAS Alarm. When the WAAS signal is lost, theOn: Alarm continues to sound until the. WAAS positioning mode is availableOn, Off. OffCorrections. Data. Selects the type of message for WAASNEXT key several times to show the “FINISH AND EXIT INSTALLATION WIZARD”Choose appropriate setting and then pressDescription of items in “port” menus. Item. Description. Settings. Default Setting. Output Format. Selects NMEA output version for theNMEA0183 Ver. 1.5. NMEA0183 Ver. 2.0. NMEA0183 Ver. 2.0. Baud Rate. Sets baud rate. DATA2 port:XTE Format. Selects number of XTE digits toSelects whether to output route (dataYes, No.

NoUse this key to view which sentences are being output. See the example below. For use only with device having.

7 Vpp, Output impedance 75. Synchro signal: H 31.5 kHz, V 60Hz (Separate), TLL levelChoose a monitor whose aspect ratio is 4:3, for example, VGA, SVGA, XGA, SXGAX. VXGA, QXGA, etcThree-or-more-unit NavNet system. Radar Antenna Unit,Radar Antenna Unit,Plotter dataSounder data. Facsimile data. Network SounderFacsimile. ReceiverNetwork SounderThree-or-more-unit NavNet system. Two-unit NavNet system. Radar Antenna Unit,Radar Antenna Unit,Radar, plotter data. Two-unit NavNet systemThose items contain organic solvents thatThe control unit can be mounted on a desktop or flush mounted in a console or panel. ForWhen selecting a mounting location for the control unit keep the following in mind. Keep the control unit out of direct sunlight. The temperature and humidity at the mounting location should be moderate and stable. Locate the unit away from exhaust pipes and vents. The mounting location should be well ventilated. Mount the unit where shock and vibration are minimal. Keep the unit away from electromagnetic field generating equipment such as motorsFor maintenance and checking purposes, leave sufficient space at the sides and rear ofMinimum recommended space is shown in the outlineA magnetic compass will be affected if the control unit is placed too close to it. ObserveFlush mounting. Follow the procedure below to mount the control unit in a panel, using accessoriesYou need a junction box and optional cable MJ-A6SPF0003-050 or MJ-A6SPF0009-100.Type: Insulation. NETWORK port. Other NavNet equipment should be connected to this port with the optional MJ-A6SPF0014RadarNavNet radar. Plotter. Network sounder. OtherPOWER BoardSlotCable tieShield. SlotPower supply unit, cover removedTo prevent strain to the cable MJ-B24LPF0009-050, fasten a cable tie (local supply) at theCablingPOWER Board 03P9419Antenna cableThe jumper block JP1 and slide switch S112 on the PWR board (03P9419) must be setOpen the unit, locate JP1 and S112 and set them as below.

Jumper block JP1Slide switch S112Jumper block, slide switch. Function. SettingDownward positionPower requirement. The power for the power supply unit and display unit must be drawn from the same powerOther Equipment. Processor unitOther Equipment. Power supply unitOther Equipment. Ship's power terminal board. Wiring processor unit and power supply board to power terminal board. Replacement of the fuse. The power supply unit is shipped with a 15 A fuse. Replace the 15 A fuse with a 7 A fuseThe fuse in the processor unit is also 15 A. Replace it with a 3A fuse.After you have installed the equipment, set up the equipment with the installation wizard. The wizard allows you to easily set up the NavNet network (choose source of radar,ENTER soft key.Then, the SELECT MODE windowTo use the settings of another NavNet unit, insertIf not, hit the CLEAR key. If you loaded settings, the message “LOADING COMPLETED.Improper setting will damage the equipment.Installation wizard, units of measurementOne of the following windowsTIME OFFSET allows you to use local time (instead of UTC time). Set the timeNETWORK SETUP menu appears. This is where you set up your NavNet network. SeeIf you have no other NavNetOne of the followingIf you set DEVICE NO.Radar Antenna. Echo. SounderDevice 1Device 2Device 3Device Number - 1. Device Number - 2. Device Number - 3. Radar Source - 1. Radar Source - 1. Radar Source - 1. Sounder Source - ETR0. Sounder Source - ETR0. Sounder Source - ETR0. Aux Source - AUX1. Aux Source - AUX1. Aux Source - AUX1One of the followingIf you set DEVICE. NO. or RADAR SERVICE, turn the power on and off again at the completion of theSelect MAGNETIC when connecting with a magnetic compass, or select TRUE whenFor the MODEL 1954C-BB or 1964C-BB, follow the procedure in the illustration at theFor other models, go to step 23.SW1 on the POWER Board upward (tuning position).